CCCUK logo

 Lancaster Insurance

Website Control

Recent threads

New Forum Posts

» Weather predicting by Rich on Thu 26 Apr 18 18:31

» Now we're digital - Membership Renewals by Alan305 on Thu 26 Apr 18 18:11

» Corvette Nationals 2018 - pre booking. by ciro_ciampi on Thu 26 Apr 18 17:30

» camaro 1988 5.0L V8 for sale by JJVETTE on Thu 26 Apr 18 11:22

» C3 Corvette Body Trolley / Stand by JJVETTE on Thu 26 Apr 18 11:16

» Waxoyl or 3m schutz?! by roppa440 on Thu 26 Apr 18 08:55

» Bolton to Haywards Heath by Sea5 on Thu 26 Apr 18 08:46

» New Exhaust System by eurovettes on Wed 25 Apr 18 13:59

» exhaust for 73 small block by JJVETTE on Wed 25 Apr 18 13:35

» Air con pump by Celcius on Tue 24 Apr 18 17:43

» How do you get a l48 to 300 ish hp or engine swap by roscobbc on Tue 24 Apr 18 15:24

» Importing C4, but need to temporarily register in the UK by rayquayle on Tue 24 Apr 18 14:15

» What did you do with your Vette today? by stevel98 on Tue 24 Apr 18 11:35

» 1990 zr1 power key by Leadfootnlazy on Mon 23 Apr 18 22:06

» Touch up kits for my 1979 coupe by JJVETTE on Mon 23 Apr 18 21:32

» Stroud Classic Car Show by curious bystander on Mon 23 Apr 18 16:04

» Harmonic balancer by Vetteheadtony on Sun 22 Apr 18 20:39

» Hand break adjustment by roscobbc on Sun 22 Apr 18 20:36

» Speedfest 2018 by Celcius on Sun 22 Apr 18 17:44

» Croyden Classic Car + Fun day by curious bystander on Sun 22 Apr 18 16:35

» 2019 Zr1 by roscobbc on Sat 21 Apr 18 18:59

» Wanted: C5 Z06 by yenko 1969 on Sat 21 Apr 18 17:42

» 1993 Cutting Out by Vetteheadtony on Sat 21 Apr 18 16:30

» Concours of Elegance by curious bystander on Sat 21 Apr 18 09:05

» Sunday Scramble - Bicester Heritage Centre by Daytona Vette on Fri 20 Apr 18 12:53

» C2 Vert Yellow by Daytona Vette on Fri 20 Apr 18 11:55

» '64 "Survivor" C2 Corvette 327ci 365hp Roadster Just Arrived by stevel98 on Fri 20 Apr 18 09:00

» 1981 corvette 64,000 mile on it way over by Vetteheadtony on Thu 19 Apr 18 10:40

» C4R-FEST tickets by curious bystander on Wed 18 Apr 18 15:35

» Corvette C6 oil filter and correct Oil / Owners manual by Eddie101 on Wed 18 Apr 18 13:08

SBC engine


Go to page: Previous / 1, 2, 3


Reply to topic
View previous topicEmail to a FriendPrinter FriendlyView next topic

Author

Message

roscobbc

Committee Member

Fri 29 Dec 17 13:17

Re: SBC engine


Vacuum line to distributor really needs to come from a direct source I.e inlet manifold rather than port on carb.


--------------------
CCCUK Chairman & Editor, Vette News
'68 coupe - 4 speed - 3.08 - 489 cu in - 570 bhp @ 5850 rpm - 606 ft/lbs torque (821 Newton Metres) @ 3850 rpm
Image

Reply with quote

roppa440

Club Member

Fri 29 Dec 17 22:46

Re: SBC engine


You need the 23 degrees initial timing so you have to restrict the total timing so it does not go over 36 mechanical only.

Where on the carb are you connecting the vacuum advance?

If you use a port on the base of the carb that sources vacuum from below the throttle blades instead of above them that should give you manifold vacuum and that will vacuum advance the timing at idle to give you enough initial without effecting total mechanical advance.

Reply with quote

Dellb

Club Member

Sat 30 Dec 17 10:53

Re: SBC engine


Hi All
The amount of expertise out there is quite awesome. You guys have really helped.
Back to my problem.
My current vacuum setup is

Main 12mm take off below throttle plates under secondary bowl is to the brake servo.
6mm take off half way up the primary metering block is to the distributor vac.

6mm take off under primary throttle plates was blanked, but is now connected to a PCV system that I have installed on the engine. I am keen to keep this, because not only does it keep the engine clean, but I believe it takes the pressure off the rear main bearing seal.
From the inlet manifold there is a connection that services the following.
Gearbox vacuum actuator
Headlights
heating and AC controls (currently being used for the vac gauge)
My plan is to blank the current distributor connection and tee the distributor into the gearbox vacuum actuator.
I will then set the initial to 15 degrees and see what the vacuum does to it.
For info, my engine is not a stock 350, but is a 400 SBC.
Rgds
Delb


--------------------
Derek L G

Reply with quote

roscobbc

Committee Member

Sat 30 Dec 17 11:30

Re: SBC engine


Dellb wrote (View Post):Hi All
The amount of expertise out there is quite awesome. You guys have really helped.
Back to my problem.
My current vacuum setup is

Main 12mm take off below throttle plates under secondary bowl is to the brake servo.
6mm take off half way up the primary metering block is to the distributor vac.

6mm take off under primary throttle plates was blanked, but is now connected to a PCV system that I have installed on the engine. I am keen to keep this, because not only does it keep the engine clean, but I believe it takes the pressure off the rear main bearing seal.
From the inlet manifold there is a connection that services the following.
Gearbox vacuum actuator
Headlights
heating and AC controls (currently being used for the vac gauge)
My plan is to blank the current distributor connection and tee the distributor into the gearbox vacuum actuator.
I will then set the initial to 15 degrees and see what the vacuum does to it.
For info, my engine is not a stock 350, but is a 400 SBC.
Rgds
Delb

It sounds as though you have matters in hand - your plans for the vacuum take-off are fine and will give a 'proper' vacuum signal rather than 'ported' signal from side of carb. 15% initial seems a good starting point to start with. If the distributor is stock you may want to consider replacing with a performance unit that has an adjustable advance curve and total figure - or - as an interim thing initially source a pack of different strength springs and bob weights to alter the advance 'curve' - perhaps bringing the advance-in much earlier (Moroso used to supply one of these). You'll need to be careful using an auto transmission though not to 'load' the engine and create detonation with too much advance - even more so if you are using the stock torque converter and a 'low' numerical axle ratio.



Last edited by roscobbc on Sat 30 Dec 17 11:32; edited 1 time in total. [2 %]
--------------------
CCCUK Chairman & Editor, Vette News
'68 coupe - 4 speed - 3.08 - 489 cu in - 570 bhp @ 5850 rpm - 606 ft/lbs torque (821 Newton Metres) @ 3850 rpm
Image

Reply with quote

roppa440

Club Member

Sun 31 Dec 17 00:36

Re: SBC engine


Using vacuum advance is handy because when the engine is put under load the vacuum drops off and so it does not cause detonation. It's the same a WOT.

You really need an adjustable timing light that allows you to set the total mechanical timing to 36 degrees max all in at 3000 rpm with half that timing in at 2000 rpm.



Last edited by roppa440 on Sun 31 Dec 17 00:37; edited 1 time in total. [6 %]

Reply with quote

Dellb

Club Member

Fri 12 Jan 18 21:45

Re: SBC engine


Hi All
I just thought I would take time to complete this thread. I have listened to the advice given, and it was spot on.

I purchased an advance timing light, and it is brilliant. It takes all the guesswork out of setting and measuring the timing.

I have set the carb as discussed, and the engine now idles well (it will never be smooth with this cam) is responsive with crystal clear exhaust.

Many thanks to you all for your advice.

Derek


--------------------
Derek L G

Reply with quote

roppa440

Club Member

Sat 13 Jan 18 17:37

Re: SBC engine


Well done! Clap Thumbs up

Reply with quote

Reply to topic
View previous topicEmail to a FriendPrinter FriendlyPrivate MessengerView next topic

Go to page: Previous / 1, 2, 3


Permissions

You cannot post new threads in this forum
You cannot reply to threads in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot add events in this forum
You cannot attach files in this forum
You cannot download files in this forum