C3 - 1975 Throttle cable where to buy the right one

[Giu]

Hi guy, I need you advice, someone can point me in the right direction, my nechanic is struggling to find the correct throttle cable for my car, could a generic GM cable suit the purpose?
like this one? Thank you in advance!!!

Universal Throttle Cable Braided Stainless Steel Wire 24" For Ford GM and More | eBay

Throttle Cable Style: Braided stainless wire. Cable Jacket Material: Rubber. Cable Length (in): 24.000 in. We will reply you within 24- 48 hours.

www.ebay.co.uk

 

[teamzr1]

The one you're looking at is "universal" I doubt fits for 1975 MY as GM made a change for that in 1975

Here is stock one to compare to

Amazon.com

75-81 Accelerator / Throttle Cable - Reproduction

75-81 Accelerator Cable - Reproduction

www.corvettecentral.com

Some info might help

TV & throttle cable (74) pics included

Hello all, I swapped my motor over to a crate which comes with a Holley. The TV & throttle cable bracket can be found & also the overdirve kickdown bracket (holley). The thing is, 74 is again a specific year. The throttle cable changed in 1975 and I think that one would clip into the bracket...

www.digitalcorvettes.com

 

[Emc]

I have 3 in stock

 

[Giu]

I have 3 in stock

This comes handy, I'll send you a message ASAP thank you

 

[Mad4slalom]

The one you're looking at is "universal" I doubt fits for 1975 MY as GM made a change for that in 1975

Here is stock one to compare to

Amazon.com

75-81 Accelerator / Throttle Cable - Reproduction

75-81 Accelerator Cable - Reproduction

www.corvettecentral.com

Some info might help

TV & throttle cable (74) pics included

Hello all, I swapped my motor over to a crate which comes with a Holley. The TV & throttle cable bracket can be found & also the overdirve kickdown bracket (holley). The thing is, 74 is again a specific year. The throttle cable changed in 1975 and I think that one would clip into the bracket...

www.digitalcorvettes.com

I have an issue with my 72 , the cable it came with is too long and makes two 90’ bends and is worn. I ordered a replacement but that is the same length. I am having it shortened by 5 cm and hopefully the company can add an adjuster as well. This slight reduction should exit the firewall and go almost straight to the carb clamp. I will report back when It is done

 

[Roscobbc]

I have an issue with my 72 , the cable it came with is too long and makes two 90’ bends and is worn. I ordered a replacement but that is the same length. I am having it shortened by 5 cm and hopefully the company can add an adjuster as well. This slight reduction should exit the firewall and go almost straight to the carb clamp. I will report back when It is done

If the OEM carb has been swapped-out for different carb (especially if inlet has been changed too) the stock cable may not be suitable.......

 

[Mad4slalom]

If the OEM carb has been swapped-out for different carb (especially if inlet has been changed too) the stock cable may not be suitable.......

Yes, my inlet is an aftermarket ali performance one with holley 650 dp. The PO had used a stock cable with the holley bracket but I was never happy with the excess cable bending r and then L around the ignition shielding bracket. Hopefully this new shortened version will sort things out.

 

[Roscobbc]

Yes, my inlet is an aftermarket ali performance one with holley 650 dp. The PO had used a stock cable with the holley bracket but I was never happy with the excess cable bending r and then L around the ignition shielding bracket. Hopefully this new shortened version will sort things out.

Similar issue to what I experienced only in my case the original cable was too short - seem to recall sourcing an aftermarket unit which helped to a degree.......but a '68 has another of those 'one-off' '68 specific things - a gas pedal assembly which not adjusted-up sufficiently seems to only just have enough travel to open the secondaries about 3/4 of the way........so you need to bend the gas pedal linkage and try to avoid (in the exitement perhaps of a 'match' race) burying your right foot too hard and deep in the carpet.......or you'll risk bending it........well known thing with 68's on the USA Corvette Forum!

 

[Emc]

When changing intakes it's always best to use the manufacturer cable bracket.

 

[Mad4slalom]

When changing intakes it's always best to use the manufacturer cable bracket.